shmups.system11.org

Shmups Forum
 
* FAQ    * Search
 * Register  * Login 
It is currently Sat Oct 31, 2020 4:29 pm View unanswered posts
View active topics



Post new topic Reply to topic  [ 106 posts ]  Go to page Previous  1, 2, 3, 4
Author Message
 Post subject: Re: An actual SNES mod to sharpen the pixels of 2-CHIP conso
PostPosted: Wed Aug 19, 2020 12:25 pm 



Joined: 27 Sep 2019
Posts: 37
Nice result! It definitely looks better than what I tested back then. Other than differences in the mod board design, the quality difference may also be due to the SHVC-CPU-01 board revision you used, since it probably has way better analog signal isolation than the GPM-02 board I have. The image looks a little under-compensated since the blur is still slightly visible in some areas though. I'm sure the sharpness test screen in the 240p test suite is a less flattering as well.

I think it's possible to improve the image further without resorting to the digital outputs, but I just have a theory and no practical implementation of said theory at the moment.


Top
 Offline Profile  
 
 Post subject: Re: An actual SNES mod to sharpen the pixels of 2-CHIP conso
PostPosted: Thu Aug 20, 2020 4:19 am 


User avatar

Joined: 24 Jul 2016
Posts: 303
unmaker wrote:
Overall I'm very pleased with the results but things are still not perfect. There is some noise that I think is a result of overshoot or ringing which Voultar mentioned in his post. I'm wondering if this mod can be further improved upon or if this is the best that it gets without resorting to say the digital RGB mod that Opatus is working on.


TY for sharing that info! I'm going to order a couple of Borti's bypass boards and try those on the end of the chain.


Top
 Offline Profile  
 
 Post subject: Re: An actual SNES mod to sharpen the pixels of 2-CHIP conso
PostPosted: Thu Aug 20, 2020 6:03 pm 


User avatar

Joined: 12 Jul 2007
Posts: 5786
Location: Where the fish lives, WV
God, I really hope this pans out. There are so many people that would appreciate something to make their SNES' picture look better, without having to resort to getting a 101. The RGB output on the original SNES is really bad.
We all know that, but it bears repeating. :lol:
_________________
My Collection: http://www.rfgeneration.com/cgi-bin/col ... Collection


Top
 Offline Profile  
 
 Post subject: Re: An actual SNES mod to sharpen the pixels of 2-CHIP conso
PostPosted: Wed Aug 26, 2020 9:34 pm 



Joined: 14 Jul 2020
Posts: 15
Just finished. Not the prettiest but it works. Seems to be a slight but noticeable improvement

Image


Top
 Offline Profile  
 
 Post subject: Re: An actual SNES mod to sharpen the pixels of 2-CHIP conso
PostPosted: Tue Sep 08, 2020 5:35 pm 



Joined: 29 Aug 2020
Posts: 1
Hi everyone! After a couple of years since I saw this mod for the first time, I finally decided to give it a try, and the result surprised me greatly. Of course it is not perfect, as there are some noticeable ringing artifacts here and there, but in overall terms, I think that the image quality is closer to a 1-chip than to a stock 2-chip. So, in opinion, the mod worth it.

For anyone interested in the details, I installed the mod on a japanese NTSC SNS-CPU-RGB-02. This board has a slightly different analog video path, as can be seen in the following image:

Image

Between the PPU2 and the video encoder, there is only one PNP common-collector stage, instead of 2. The RGB signals on the multiAV come from the video encoder, instead of coming directly from the transistor. For this reason, I had to add the missing common-collector stage, using three aditional transistors. I used the SMD version of the BC857, which seems to work well. I also used LL4148 (SMD version of 1N4148) for the diodes, and replaced 300 ohm, 200 ohm and 2 kohm resistors with 330 ohm, 220 ohm and 2k2 ohm ones, which are easier to find.

For the PCB, I made my own home-made design. Here is the board installed (forget about the green wires at the IC, I accidentaly swaped IN+ and IN- inputs on two of the three amplifiers when designing the board):

Image

I lifted the base of transistors Q1, Q2 and Q3, took the original RGB signals from the PCB pad, and reinjected the modified signals at the transistors bases. I also lifted PPU2 pin 3, to remove the diagonal chroma sub-carrier interference (this is something almost mandatory in this board revision).

Here are some comparisons before and after the mod. The console is directly connected to a Framemeister and the image is upscaled to 1080p. Sorry for the quality, I don't have any capture device, so I had to photograph the TV with the phone:

Image
Image
Image
Image

I hope someone find this information useful.


Top
 Offline Profile  
 
 Post subject: Re: An actual SNES mod to sharpen the pixels of 2-CHIP conso
PostPosted: Tue Sep 15, 2020 10:40 am 



Joined: 27 Sep 2019
Posts: 37
Looks good! It's interesting to see different board layouts for that circuit.

I took a break from messing with this project for a month and just got back to it last week. My first adapter board didn't function properly. Graphical glitches and freezing everywhere. Not sure if I damaged the PPU2 chip or it was just bad soldering or something else, but I have more from a parts pile if needed.


Top
 Offline Profile  
 
 Post subject: Re: An actual SNES mod to sharpen the pixels of 2-CHIP conso
PostPosted: Sun Sep 20, 2020 3:46 pm 



Joined: 23 Oct 2017
Posts: 13
Wow! This thread is awesome! Thanks to all who have worked on this or tried this!

Just one question. How does RGB with and without this mod compare to straight S-Video? I've been using S-Video on a consumer CRT and it looks pretty good to me. But when I look at RGB pics of non-modded 2 chips like mine it looks like a step down. Maybe it's just the close up effect.


Top
 Offline Profile  
 
 Post subject: Re: An actual SNES mod to sharpen the pixels of 2-CHIP conso
PostPosted: Sun Sep 27, 2020 2:51 pm 


User avatar

Joined: 12 Jul 2007
Posts: 5786
Location: Where the fish lives, WV
Any chance of this improving any more? Or is this the final form?
_________________
My Collection: http://www.rfgeneration.com/cgi-bin/col ... Collection


Top
 Offline Profile  
 
 Post subject: Re: An actual SNES mod to sharpen the pixels of 2-CHIP conso
PostPosted: Mon Sep 28, 2020 3:26 pm 



Joined: 27 Sep 2019
Posts: 37
I’ve been meaning to write up my thoughts on the Japanese mod. Now that I gained a little bit of experience from designing my own circuit, I think I understand enough about circuits to make some comments and suggestions for improvement. Still, I’m not an electrical engineer, so I could be wrong or misinformed on some details. It’s going to be technical, but hopefully someone here will understand it:

1. The first PNP buffer is driving a rather heavy load. This is mainly due to the 300Ω resistor terminated to VCC. For the AC part of the signal, the equivalent parallel resistance seen by the emitter is 279Ω, or 300Ω || (2kΩ + (2kΩ || 3MΩ)). This probably puts too much of a load on the unbuffered PPU2 signal, resulting in nonlinear distortion. Depending on the transistor grade (FQ, FR, FS), the base input resistance can be anywhere from 33.5kΩ to 156kΩ, which is quite low. For example, the THS family of video buffers have an input resistance of 800kΩ, and op amp input buffers are typically in the MΩ to GΩ range. Raising all the resistor values by one order of magnitude (3kΩ and 20kΩ) should reduce distortion and draw less current.

2. The output voltage swing of the LMH6683 is within 0.8V from the rails (VCC and GND) under a 2kΩ load. This means that the signal needs to be within 0.8V – 4.2V, assuming VCC is 5V. The circuit applies a load smaller than 400Ω at the op amp output due to the feedback and gain resistors, so that may shrink the linear region further. A single PNP buffer voltage offset is typically around 0.6V, so it isn’t enough to push the signal safely into the linear region of the op amp, resulting in more distortion at the lower end of the signal. The solution is to either add a little more DC offset or choose a different op amp that can swing well below 0.6V from the rails. Maybe it would have been better to apply the circuit after both PNP transistors? That way, the current gain is much higher, and the DC offset is about 1.2V. There are a bunch of ways to approach this.

I think replacing the op amp with a rail-to-rail, unity-gain-stable type would eliminate a lot of issues. The LMH6683 doesn’t appear to be unity gain stable, and that’s why the signal is attenuated by 6dB and amplified by 6dB. The voltage dividers seem to be the cause of unnecessary loads on the circuit. With a unity gain stable amp, the two 2kΩ resistors can be eliminated and the 300Ω one replaced with a much higher value like 10kΩ. The stock circuit already has a 10kΩ resistor between the first PNP emitter and VCC, so you will only need to tap the emitter pin to get your input. Furthermore, the 200Ω gain resistor can be removed and the 200Ω feedback resistor replaced with 100Ω to compensate. This will reduce the parts count and current load due to the elimination of low-valued resistors terminated to GND or VCC.

Anyway, those are my thoughts. I’m still not quite sure how the overshoot-limiting portion of the circuit works (it starts from the 47Ω output resistor, follows though the 2 diodes and finally the 1000pF series capacitor). My own approach is a little bit different, but I don’t know if it makes that much of a difference overall. Hope this helps anyone who wants to tweak the mod further.


Top
 Offline Profile  
 
 Post subject: Re: An actual SNES mod to sharpen the pixels of 2-CHIP conso
PostPosted: Fri Oct 16, 2020 10:56 am 


User avatar

Joined: 24 Jul 2016
Posts: 303
Unmaker, did you use 75R resistors for R11,R21,R31 to adjust the brightness? May I ask what moved you to populate those spots at all, when the instructions say to leave blank for 2-chip SNES models?

unmaker wrote:
Although the blur was greatly reduced, the output was way too bright. So I went a step further and installed borti4938's RGB bypass mod:

https://github.com/borti4938/SNES_RGB_B ... 1-reported

Image

With the brightness attenuated things looked so much better. Borti's mod also appeared to help with blur reduction but this could be because it was now less bright. Hard for me to tell here.


Top
 Offline Profile  
 
 Post subject: Re: An actual SNES mod to sharpen the pixels of 2-CHIP conso
PostPosted: Sat Oct 17, 2020 9:26 pm 


User avatar

Joined: 17 Jan 2016
Posts: 301
Has this been distilled down to a purchasable ready to install board?


Top
 Offline Profile  
 
 Post subject: Re: An actual SNES mod to sharpen the pixels of 2-CHIP conso
PostPosted: Sun Oct 18, 2020 11:21 pm 


User avatar

Joined: 24 Jul 2016
Posts: 303
LDigital wrote:
Has this been distilled down to a purchasable ready to install board?


No. At least, not by me. The problem is that while the video filter mod board is an improvement in the opinion of most people, it introduces the overshoot problem discussed earlier. I'm going to try out Borti's bypass board as @unmaker did, and see how much i think that helps.

But then it's a two-board solution. I haven't even looked at the schematics to see where else the post-filter video signal goes, so i'm not sure there's going to be an elegant solution. And if there is, i'm not setup to sell it. I'd leave that part to someone else.


Top
 Offline Profile  
 
 Post subject: Re: An actual SNES mod to sharpen the pixels of 2-CHIP conso
PostPosted: Mon Oct 19, 2020 4:14 am 



Joined: 27 Sep 2019
Posts: 37
I think the overshoot problem will be difficult to solve using pure analog components. For now, the easiest thing to do is to hide most of it though optimal digital sampling. I guess that's not a sensible option on a 15 KHz CRT TV though. Maybe some new innovations (sans the digital mod) can improve the signal better than the way it's being done at the moment.

I'm not exactly sure how adding borti's bypass board helps with brightness. The Japanese RLPF mod outputs at the same levels as the input, with some attenuation and distortion due to the issues I described earlier. It looks like unmaker simply terminated the signal with 75 ohm resistors to drop it to 700 mV because the THS driver has a fixed 6 dB gain. It would actually have to be terminated at < 75 ohms if the picture was too bright for him. I'm not sure exactly what's going on because it should've been at the proper levels to begin with.


Top
 Offline Profile  
 
 Post subject: Re: An actual SNES mod to sharpen the pixels of 2-CHIP conso
PostPosted: Mon Oct 19, 2020 8:28 am 


User avatar

Joined: 24 Jul 2016
Posts: 303
Internal to the shvc-cpu-01 model, Borti's bypass board doesn't require the terminators on the amp inputs. 75R terminations are specified for use on 1chip models, and 1.2K on SNES2 models. Which is why i was confused.

Still willing to give it a shot, it shouldn't hurt anything.


Top
 Offline Profile  
 
 Post subject: Re: An actual SNES mod to sharpen the pixels of 2-CHIP conso
PostPosted: Tue Oct 20, 2020 2:45 am 



Joined: 27 Sep 2019
Posts: 37
I took a look at the instructions for the mod and it looks like it requires the removal and replacement of some motherboard components and different solder points. You can repurpose the mod to simply terminate the signal and amplify it back up if you understand the whole circuit well enough.


Top
 Offline Profile  
 
 Post subject: Re: An actual SNES mod to sharpen the pixels of 2-CHIP conso
PostPosted: Thu Oct 29, 2020 11:03 am 


User avatar

Joined: 24 Jul 2016
Posts: 303
yoshiyukiblade wrote:
I took a look at the instructions for the mod and it looks like it requires the removal and replacement of some motherboard components and different solder points. You can repurpose the mod to simply terminate the signal and amplify it back up if you understand the whole circuit well enough.


Well, i have to admit i don't understand it. What are you saying in particular though - use the 75R resistors for R11, R21, R31? Don't use them?


Top
 Offline Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 106 posts ]  Go to page Previous  1, 2, 3, 4

All times are UTC


Who is online

Users browsing this forum: Ryoandr, Solidzera and 20 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
Space Pilot 3K template by Jakob Persson
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group