Lumagen VisionPro HDP complete list of remote commands

Konsolkongen · Post by **Konsolkongen** » Mon Dec 01, 2014 8:13 pm

Here's a complete list of remote commands for the Lumagen VisionPro HDP I found by trial and error. It's quite a few more than what's listed in the manual. I'm listing them here in case I ever loose the file, but it might be of help to others too

Some of the values listed next to the options was the default values for me. These might be different for you, or depend on the connected source. So be sure to write down the values yourselves, BEFORE you change anything

Code: Select all

0916 : POWER ON MSG WHEN ALREADY ON IS: (ON/OFF)
0918 : LIVE FLAGS (ON/OFF)
0919 : RE-INIT INPUT WHEN SELECTED AND ALREADY CURRENT: (ON/OFF)
0910 : SERVICE MENU IS (ON/OFF)
0921 : EXT SWITCH ON
0922 : EXT SWITCH OFF
0923 : ZOOM SET TO (5%/DEFAULT)
0925 : LIGHTS (ON/OFF)
0926 : INPUT 100 IRE WINDOW PATTERN TO CALIBRATE - PRESS OK WHEN READY - '0' FOR STATUS, '5' RESETS, EXIT QUITS
0929 : PAGEFLIP :(FAST/NORM)
0931 : SOFTWARE UPDATE?
0932 : OUTPUT - 1=AUTO 2=DVI 3=ANA 4=BOTH
0933 : SET PCLK:0 - CURRENTLY 148354343 (Dreamcast)
0934 : TEST DVI OUT
0936 : TV BLCK LEVEL: 5
0937 : TV GAIN LEVEL: 128
0938 : MACROVISION BLCK OFFSET: 0
0939 : MACROVISION CONT OFFSET: 4
0941 : Same as OUT > RES > TIMING
0942 : ADJUST SIZE
0944 : ADI SYNC LEVEL:24
0945 : NSOPT :(ON/OFF)
0948 : INVERSE 709->601 RGB:(ON/OFF)
0940 : HSYNC WIDTH: 88
0951 : DEINT (ON/OFF)
0952 : SPLIT SCRN DEINT (ON/OFF)
0954 : DEINT NOISE REDUCTION (ENABLED/DISABLED)
0961 : Gives the following menu:
	LUMA FILT (COMB/TRAP)
	LUMA NTCH (NONE/NOTCH1/NOTCH2/NOTCH3)
	WBAND CHROMA FILT (ON/OFF)
	CHROMA NTCH (NOTCH1/NONE/NOTCH3/NOTCH2)
	DEFAULTS - PRESS <> TO RESET
0964 : NO SIG MSG:(ON/OFF)
0966 : INPUT 100 IRE WINDOW PATTERN TO CALIBRATE - PRESS OK WHEN READY - '0' FOR STATUS, '5' RESETS, EXIT QUITS
0967 : PAL CALC (NEW/OLD)
0968 : HDCP in :128,128,128,128
0969 : HDCP del:50
0960 : Gives the following menu:
	AUTO
	NTSC
	PAL
	PAL-M
	PAL-Nc
	NTSC4.43
	SECAM
0971 : 1.85 KEY FUNCTION: (1.85/2.35)
0974 : SDI CABLE EQ: (ON/OFF) - ENABLE IF >10 METER
0987 : SIDEBAR PAN (ON/OFF)
0995 : IR LOCKED
0996 : IR LIMIT (ON/OFF)
0997 : MUST ENABLE SERVICE MODE FIRST <AFTER SERVICE> PRESS OK TO BACKUP ISF CONFIG
0998 : RESET OUTPUT MODE TO FACTORY DEFAULTS
0999 : RESET TO FACTORY DEFAULTS

011 : YPRPB HD (TRI/BI)
012 : RGB H and V-sync inversion menu
013 : RGBS sync inversion menu
014 : RGBS (TRI/BI)
015 : YPRPB SD (TRI/BI)

02X : Various output resoltions

03 : ENTER VRES: 0
04 : ENTER VRATE: 0
05 : ENTER HRATE: 0
06 : ENTER ASPECT:0.00
07 : ENTER HRES: 0

0888 : PRESS OK TO RESTORE ISF SETTINGS