Bitfunx Dreamcast Component Cables
-
- Posts: 101
- Joined: Sun Jun 15, 2014 11:08 pm
Bitfunx Dreamcast Component Cables
I figured I'd give a really quick review of these https://www.bitfunx.com/product/rgbs-vg ... e-console/
I also own the retrogamingcables cable, which are almost always out of stock. I couldn't find a single review of these cable outside of that "they work". From side by side comparisons I can see absolutely no discernable difference with the RGC cables with 480p output to an HD CRT. No noise, no sync issues, exact same coloration. Greyscale and color bars look identical. The only noticeable difference is the Bitfunx image is properly centered like all my other systems, whereas the RGC cable is offset to the right unfortunately.
Morals aside as I know some people have issues with these aliexpress companies, this is probably the best component cable available for the Dreamcast even if the others were in stock. The cable itself appears to be identical to that used in HD Retrovision cables, I have no doubt it's properly shielded 75ohm cabling. I might actually end up ordering a 2nd cable to replace my RGC cable and have a centered image.
I also own the retrogamingcables cable, which are almost always out of stock. I couldn't find a single review of these cable outside of that "they work". From side by side comparisons I can see absolutely no discernable difference with the RGC cables with 480p output to an HD CRT. No noise, no sync issues, exact same coloration. Greyscale and color bars look identical. The only noticeable difference is the Bitfunx image is properly centered like all my other systems, whereas the RGC cable is offset to the right unfortunately.
Morals aside as I know some people have issues with these aliexpress companies, this is probably the best component cable available for the Dreamcast even if the others were in stock. The cable itself appears to be identical to that used in HD Retrovision cables, I have no doubt it's properly shielded 75ohm cabling. I might actually end up ordering a 2nd cable to replace my RGC cable and have a centered image.
-
- Posts: 101
- Joined: Sun Jun 15, 2014 11:08 pm
Re: Bitfunx Dreamcast Component Cables
I appear to have spoken too soon... After a couple hours of gameplay I started getting a very light scrolling horizontal noise on some scenes, swapping cables while still running fixed this each time. I've played hundreds of hours on the Rgc cables, same Dreamcast and setup and never had this.
I'll probably open these up and take a look what they've actually done and post up some pictures.
I'll probably open these up and take a look what they've actually done and post up some pictures.
Re: Bitfunx Dreamcast Component Cables
Thanks for your review. After reading your first post I was going to jump on the train and order a pair but that scrolling issue worries me ![Sad :-(](./images/smilies/icon_sad.gif)
What crt did you use it on ? I have bvm d24 and I hope they don’t have that infamous banding issue in the top screen which only seem to occur on BVM D series monitors.
![Sad :-(](./images/smilies/icon_sad.gif)
What crt did you use it on ? I have bvm d24 and I hope they don’t have that infamous banding issue in the top screen which only seem to occur on BVM D series monitors.
-
- Posts: 101
- Joined: Sun Jun 15, 2014 11:08 pm
Re: Bitfunx Dreamcast Component Cables
I have a Loewe Planus, I forget the model number at the moment but it's a 60hz 1080i model.
I'm actually having no luck reproducing the issue with noise. Original I played a couple hours with these cables, noticed it, plugged in the RGC cable and it was gone, plugged the bitfunx back in and it returned, did that a couple times and walked away. Went back to do some more testing and can't get it to have issues again. I can say the cables initially were an extremely tight fit, perhaps a pin wasn't making the greatest contact, the RGC cables never fit great either, they don't get audio sometimes and have to be plugged in extremely hard.
I'm going to play around more today and see if this happens again, I'd really like these cables to work as intended since they're readily available, have a centered image, and initially were giving an image that matched the RGC cable. It seems to only be one color channel that had issues, as it was very specific images on screen that it was visible on. If I can get it to happen again I could test more.
I'm actually having no luck reproducing the issue with noise. Original I played a couple hours with these cables, noticed it, plugged in the RGC cable and it was gone, plugged the bitfunx back in and it returned, did that a couple times and walked away. Went back to do some more testing and can't get it to have issues again. I can say the cables initially were an extremely tight fit, perhaps a pin wasn't making the greatest contact, the RGC cables never fit great either, they don't get audio sometimes and have to be plugged in extremely hard.
I'm going to play around more today and see if this happens again, I'd really like these cables to work as intended since they're readily available, have a centered image, and initially were giving an image that matched the RGC cable. It seems to only be one color channel that had issues, as it was very specific images on screen that it was visible on. If I can get it to happen again I could test more.
Re: Bitfunx Dreamcast Component Cables
Thanks!
Please keep us updated with your experience.
How do they work with different output resolutions?
Please keep us updated with your experience.
How do they work with different output resolutions?
-
- Posts: 101
- Joined: Sun Jun 15, 2014 11:08 pm
Re: Bitfunx Dreamcast Component Cables
280p/480i seem to work as intended, no different than the RGC cable, just a super stiff toggle switch that works. That being said I need to run it through a GBS-C on this particular TV as it doesn't support these resolutions. I don't foresee there being any issues there though, works the same as the RGC which I have used on a 240p/480i set in the past without problem. So far the only thing that has me concerned was the noise, I don't really want to tear the housing open if I can't get it to come back though. It does appear to be 2 pieces but I doubt they'd make it easy to open unscarred.
Re: Bitfunx Dreamcast Component Cables
Do the cables have the slight green color mismatch like the RGC component cables?:-
https://youtu.be/VPqTzYFUBwo?t=356
https://twitter.com/SureWhyNotImSm1/sta ... 6554778768
https://youtu.be/VPqTzYFUBwo?t=356
https://twitter.com/SureWhyNotImSm1/sta ... 6554778768
-
- Posts: 101
- Joined: Sun Jun 15, 2014 11:08 pm
Re: Bitfunx Dreamcast Component Cables
I haven't been able to replicate that with either cable, it doesn't appear visible no matter how close I look at a scrolling or paused grid pattern. They're both extremely sharp and clear, all of 240p test suites greyscale and color patterns look sharp without bleed. Maybe with a direct capture I'd see something different.
I ran the bitfunx cables the better part of the day today with absolutely no issues. I'm sick as can be so I'll hopefully get a lot of time with them this week. So far my noise issue looks to have resolved through my repeated unplugging and replugging adventures.
I ran the bitfunx cables the better part of the day today with absolutely no issues. I'm sick as can be so I'll hopefully get a lot of time with them this week. So far my noise issue looks to have resolved through my repeated unplugging and replugging adventures.
Re: Bitfunx Dreamcast Component Cables
If its not too much to ask. Could you please take comparison pictures off your CRT?TheRetroCarrot wrote: ↑Fri Feb 16, 2024 1:10 am I haven't been able to replicate that with either cable, it doesn't appear visible no matter how close I look at a scrolling or paused grid pattern. They're both extremely sharp and clear, all of 240p test suites greyscale and color patterns look sharp without bleed. Maybe with a direct capture I'd see something different.
I ran the bitfunx cables the better part of the day today with absolutely no issues. I'm sick as can be so I'll hopefully get a lot of time with them this week. So far my noise issue looks to have resolved through my repeated unplugging and replugging adventures.
-
- Posts: 7681
- Joined: Wed Jan 26, 2005 1:28 am
- Location: Bedford, UK
- Contact:
Re: Bitfunx Dreamcast Component Cables
I don't think the RGC cable is that much of a problem off setting to the right if your using a retrotink which most would be using an upscaler with it.
Straight into a HD CRT is a different matter.
I'm using a HDMI cable right now which gives good results if your nose isn't up to the screen. Mind you, I don't think Dreamcast was ever designed for huge flat screens.
I find with these sorts of things that folk are extremely fussy when it comes to PQ that they will spend lots of money finding the best optimum solution when a cheaper solution exists that is slightly un-optimum.
Straight into a HD CRT is a different matter.
I'm using a HDMI cable right now which gives good results if your nose isn't up to the screen. Mind you, I don't think Dreamcast was ever designed for huge flat screens.
I find with these sorts of things that folk are extremely fussy when it comes to PQ that they will spend lots of money finding the best optimum solution when a cheaper solution exists that is slightly un-optimum.
This industry has become 2 dimensional as it transcended into a 3D world.
-
- Posts: 101
- Joined: Sun Jun 15, 2014 11:08 pm
Re: Bitfunx Dreamcast Component Cables
Attached some in a dropbox folder since I'd assume you'd want raw quality. RGC on the right, Bitfunx on the left. Sorry I'm not much of a photographer, and I neglected to take a photo of the colorbars on the RGC cable. Any brightness differences I can see are just from my lack of camera skills.RebeL9 wrote: ↑Fri Feb 16, 2024 9:41 amIf its not too much to ask. Could you please take comparison pictures off your CRT?TheRetroCarrot wrote: ↑Fri Feb 16, 2024 1:10 am I haven't been able to replicate that with either cable, it doesn't appear visible no matter how close I look at a scrolling or paused grid pattern. They're both extremely sharp and clear, all of 240p test suites greyscale and color patterns look sharp without bleed. Maybe with a direct capture I'd see something different.
I ran the bitfunx cables the better part of the day today with absolutely no issues. I'm sick as can be so I'll hopefully get a lot of time with them this week. So far my noise issue looks to have resolved through my repeated unplugging and replugging adventures.
https://www.dropbox.com/scl/fo/gzvl3cgr ... k6drc&dl=0
Smooshed quality:
https://imgur.com/a/sIyzrOj
Re: Bitfunx Dreamcast Component Cables
Thanks a bunch.
Yeah its hard to tell them apart from eachother judging by these pictures. Im curious to see if Bitfunx are basing their PCB on the same foundation as the RGC cable.
Yeah its hard to tell them apart from eachother judging by these pictures. Im curious to see if Bitfunx are basing their PCB on the same foundation as the RGC cable.
-
- Posts: 101
- Joined: Sun Jun 15, 2014 11:08 pm
Re: Bitfunx Dreamcast Component Cables
Looking more at these photos, the Bitfunx cables are sharper. I noticed it zoomed out on some of those comparisons, if it was just one of them I'd say it was a photography issue, but it seems consistent across the board. This wasn't noticeable A/Bing between the two, but might be more noticeable on an LCD display. Either way at this point I'd say the Bitfunx cables perform better than RGC, I still haven't had any issues with noise again.
![Image](https://i.imgur.com/tSuz4gF.png)
![Image](https://i.imgur.com/C9DjfIV.png)
Did some very minor level correction to match but the RGC is the right side of this, I'm fairly certain I see a difference in clarity in all of these shots:
![Image](https://i.imgur.com/JF7y0lq.png)
![Image](https://i.imgur.com/tSuz4gF.png)
![Image](https://i.imgur.com/C9DjfIV.png)
Did some very minor level correction to match but the RGC is the right side of this, I'm fairly certain I see a difference in clarity in all of these shots:
![Image](https://i.imgur.com/JF7y0lq.png)
-
- Posts: 7681
- Joined: Wed Jan 26, 2005 1:28 am
- Location: Bedford, UK
- Contact:
Re: Bitfunx Dreamcast Component Cables
What would cause a difference of PQ on a component cable compared to another component cable?
This industry has become 2 dimensional as it transcended into a 3D world.
-
- Posts: 101
- Joined: Sun Jun 15, 2014 11:08 pm
Re: Bitfunx Dreamcast Component Cables
In this situation I would say it's something with the active portion of this cable, as the cables themselves are both thick shielded coax which I have no doubts to the quality of.
Re: Bitfunx Dreamcast Component Cables
Where is the hype? We now practically have a readily available component cable option for Dreamcast for the first time. I'm surprised this haven't been picked up by the big youtubers such as Retro RGB, MLIG etc. While we did get a component option from RGC last year it has been out of stock since many months.
-
- Posts: 101
- Joined: Sun Jun 15, 2014 11:08 pm
Re: Bitfunx Dreamcast Component Cables
Good question, I didn't even know about these and probably never would have if they didn't pop up on aliexpress when shopping for a translucent shell.
My guess is it's because it's an aliexpress product, I've noticed the retro gaming industry tends to be a very tight knit community of distributors and creators and typically have some moral objection to companies "copying" products. After a recent experience with a company who may or may not sell gcomp switches I'm all for Bitfunx haha.
My guess is it's because it's an aliexpress product, I've noticed the retro gaming industry tends to be a very tight knit community of distributors and creators and typically have some moral objection to companies "copying" products. After a recent experience with a company who may or may not sell gcomp switches I'm all for Bitfunx haha.
-
kitty666cats
- Posts: 1274
- Joined: Tue Nov 05, 2019 2:03 am
- Location: Massachusetts, USA
Re: Bitfunx Dreamcast Component Cables
Because they all despise Kaico/BitFunx/Retroscaler etc etc for stealing designs. But hey, those companies make it so that gear is actually *readily available* and not available in ~3 day windows/getting resold for jacked-up prices like most other brands. Awkward situation for people who have strong morals about stupid video game equipmentRebeL9 wrote: ↑Wed Feb 21, 2024 1:09 pm Where is the hype? We now practically have a readily available component cable option for Dreamcast for the first time. I'm surprised this haven't been picked up by the big youtubers such as Retro RGB, MLIG etc. While we did get a component option from RGC last year it has been out of stock since many months.
-
- Posts: 3
- Joined: Thu Feb 22, 2024 5:38 am
Re: Bitfunx Dreamcast Component Cables
Have any of you tried the beharbros stuff? I was using a Pound VGA to HDMI for Dreamcast and decided to try their Akura box. It's not an upscaler but has a lot of good perks on it. Works really good. They have a lot of VGA convertors on there and it only took a week to get it delivered to Pa from Turkey.
https://www.beharbros.com/
https://www.beharbros.com/
-
- Posts: 101
- Joined: Sun Jun 15, 2014 11:08 pm
Re: Bitfunx Dreamcast Component Cables
I have a garo lite from them. It seems to function fairly well though I don't really use it any more. It was very picky about power supplies, the RGBS/RGBHV switch was broken so I ended up bridging it, and the bottom of the board was covered in what looked like dried up flux. I requested a return and they refunded the product cost minus shipping and said to keep it, make what you will of all that. I still keep it around in case I need YPbPr-RGBHV conversion without any features though, right now my GBS-C performs this with the added benefits of being able to position the image wherever.Neogeo1982 wrote: ↑Thu Feb 22, 2024 10:53 am Have any of you tried the beharbros stuff? I was using a Pound VGA to HDMI for Dreamcast and decided to try their Akura box. It's not an upscaler but has a lot of good perks on it. Works really good. They have a lot of VGA convertors on there and it only took a week to get it delivered to Pa from Turkey.
https://www.beharbros.com/
Re: Bitfunx Dreamcast Component Cables
Yeah I agree with you and I have noticed this myself. I follow some of the biggest retro gaming channels on youtube. The respected ones, not the yelling bullshit ones. The problem is as you say that it is a very tight knit community. They often refer to eachother and even participate in eachothers videos. They release reviews at the same time and of the same products. The problem with this is that it becomes to streamlined and you don't get reiews and coverage of products from AliExpress for instance.TheRetroCarrot wrote: ↑Thu Feb 22, 2024 12:23 am Good question, I didn't even know about these and probably never would have if they didn't pop up on aliexpress when shopping for a translucent shell.
My guess is it's because it's an aliexpress product, I've noticed the retro gaming industry tends to be a very tight knit community of distributors and creators and typically have some moral objection to companies "copying" products. After a recent experience with a company who may or may not sell gcomp switches I'm all for Bitfunx haha.
A good example of this is Blue Retro adapters for retro consoles. They will cover one specific adapter because the developer is someone from the west. But they wont mention that the same type of adapter is being sold on AliExpress for half the price.
Re: Bitfunx Dreamcast Component Cables
I'll 2nd Beharbros. I have a Hanzo DC VGA box from them. Top tier stuff.Neogeo1982 wrote: ↑Thu Feb 22, 2024 10:53 am Have any of you tried the beharbros stuff? I was using a Pound VGA to HDMI for Dreamcast and decided to try their Akura box. It's not an upscaler but has a lot of good perks on it. Works really good. They have a lot of VGA convertors on there and it only took a week to get it delivered to Pa from Turkey.
https://www.beharbros.com/
You're sure to be in a fine haze about now, but don't think too hard about all of this. Just go out and kill a few beasts. It's for your own good. You know, it's just what hunters do! You'll get used to it.
-
TooBeaucoup
- Posts: 399
- Joined: Fri Jun 09, 2017 1:31 am
Re: Bitfunx Dreamcast Component Cables
I would strongly urge anyone considering Beharbros to do some serious Googling before making a purchase. They have had known quality control issues on almost all of their products going back several years. Not only that, they are very unwilling to help customers when they have a problem. My $70 Toro Box never worked right since the day I got it, and it is definitely not an isolated problem across all of their products.
![Image](https://i.ibb.co/6gS6ptq/1000021899.jpg)
![Image](https://i.ibb.co/FxFs0Fq/1000021897.jpg)
![Image](https://i.ibb.co/72nn9M4/1000021898.jpg)
![Image](https://i.ibb.co/6gS6ptq/1000021899.jpg)
-
Virtual_Tintin
- Posts: 16
- Joined: Thu Feb 15, 2024 9:02 am
Re: Bitfunx Dreamcast Component Cables
to summarize, the best cable for dreamcast is the one from retro access ![Very Happy :D](./images/smilies/icon_biggrin.gif)
I played dozens of hours with it, on a bvm d-series, and magnificent image in 480p, without any problem![Wink :wink:](./images/smilies/icon_wink.gif)
![Very Happy :D](./images/smilies/icon_biggrin.gif)
I played dozens of hours with it, on a bvm d-series, and magnificent image in 480p, without any problem
![Wink :wink:](./images/smilies/icon_wink.gif)
Last edited by Virtual_Tintin on Sat Feb 24, 2024 6:54 am, edited 1 time in total.
Re: Bitfunx Dreamcast Component Cables
https://dreamcast-talk.com/forum/viewtopic.php?t=11860
Last edited by beharius on Fri Feb 23, 2024 9:08 pm, edited 1 time in total.
Re: Bitfunx Dreamcast Component Cables
They are impossible to get hold ofVirtual_Tintin wrote: ↑Fri Feb 23, 2024 8:04 pm To summarize, the best cable for Dreamcast is the one from Retro Access
I played dozens of hours with it, on a BVM D-Series, and magnificent image in 480p, without any problem![]()
![Sad :-(](./images/smilies/icon_sad.gif)
Re: Bitfunx Dreamcast Component Cables
You can always find our MAMBA cable. We mass produced them...
https://www.beharbros.com/product-page/ ... rt-dc-480p
https://www.beharbros.com/product-page/ ... rt-dc-480p
-
kitty666cats
- Posts: 1274
- Joined: Tue Nov 05, 2019 2:03 am
- Location: Massachusetts, USA
Re: Bitfunx Dreamcast Component Cables
This. Thing is brand new, seems like not many people know about it yet. A readily available multi-sync Dreamcast cable?! Impossible!beharius wrote: ↑Fri Feb 23, 2024 9:10 pm You can always find our MAMBA cable. We mass produced them...
https://www.beharbros.com/product-page/ ... rt-dc-480p
![Razz :P](./images/smilies/icon_razz.gif)
P.S. What’s the story with the new capture card, Yosi? Did you find a mass produced one that you discovered to actually be quite good, then buy a bulk order and make your own modifications to further improve the design?
Re: Bitfunx Dreamcast Component Cables
Does it have the infamous banding issue in D-series of Sony BVM monitors?beharius wrote: ↑Fri Feb 23, 2024 9:10 pm You can always find our MAMBA cable. We mass produced them...
https://www.beharbros.com/product-page/ ... rt-dc-480p
-
- Posts: 101
- Joined: Sun Jun 15, 2014 11:08 pm
Re: Bitfunx Dreamcast Component Cables
EDIT: I can't read, I've only ever meant to discuss the RGC cable, I have no experience with the retro access cable at all.Virtual_Tintin wrote: ↑Fri Feb 23, 2024 8:04 pm To summarize, the best cable for Dreamcast is the one from Retro Access
I played dozens of hours with it, on a BVM D-Series, and magnificent image in 480p, without any problem![]()
Last edited by TheRetroCarrot on Sat Feb 24, 2024 8:11 pm, edited 1 time in total.