This gear is missing on my CD-Rom (under the spoiler). Does anyone have a model for printing?
PC Engine cd-rom gear
PC Engine cd-rom gear
Hey guys.
This gear is missing on my CD-Rom (under the spoiler). Does anyone have a model for printing?
This gear is missing on my CD-Rom (under the spoiler). Does anyone have a model for printing?
Re: PC Engine cd-rom gear
These were being 3D printed as far back as I can remember, try searching open source 3D model repositories, I know there are a few. I bet you several exists on there.
Edit:
https://www.printables.com/model/79121- ... ement-gear
Edit:
https://www.printables.com/model/79121- ... ement-gear
Re: PC Engine cd-rom gear
Sadly that's the middle one that is broken on all units at this point, but the OP asks for the one under it... I've never seen that one broken or missing at all so I guess it's going to be more difficult to get some 3d model...kamiboy wrote: ↑Mon Feb 12, 2024 8:45 am These were being 3D printed as far back as I can remember, try searching open source 3D model repositories, I know there are a few. I bet you several exists on there.
Edit:
https://www.printables.com/model/79121- ... ement-gear
Re: PC Engine cd-rom gear
Oh, yeah, I guess that one breaking is quite a rare occurrence. Your best bet would prolly be to contract someone to make a replacement 3D model for printing. Someone with a bit of experience and access to the gear, even a broken one, should be able to make one in a 3D modelling program of choice. It might even be possible to make one from high quality reference photos as long as they have some reference point for scale.
Re: PC Engine cd-rom gear
I can make a model, but I don't have the original gear to accurately measure the dimensions.Tak-MK wrote: ↑Mon Feb 12, 2024 11:00 amSadly that's the middle one that is broken on all units at this point, but the OP asks for the one under it... I've never seen that one broken or missing at all so I guess it's going to be more difficult to get some 3d model...kamiboy wrote: ↑Mon Feb 12, 2024 8:45 am These were being 3D printed as far back as I can remember, try searching open source 3D model repositories, I know there are a few. I bet you several exists on there.
Edit:
https://www.printables.com/model/79121- ... ement-gear
And I can print it only once at work, using an SLA printer
Re: PC Engine cd-rom gear
Then maybe someone here would volunteer to measure theirs. Still, the chances of getting it right on first try in such a roundabout way is quite slim.
Re: PC Engine cd-rom gear
I can try to make some measurements from mine, although I don't know how to properly measure the "spikes" part...
Re: PC Engine cd-rom gear
I'll try to make a test model myself. Found some useful information. I'll post the results later.
Spoiler
-
BuffaloWing
- Posts: 50
- Joined: Tue Feb 02, 2016 1:31 am
- Contact:
Re: PC Engine cd-rom gear
You might want to use Dreamcast's gear. I have a broken laser on top of my desk and took some measurements. It has 14 teeth like your picture, so it seems like that maybe a standard... Anyway, the diameter is 4.76mm (probably 4.75m theoretically), overall length along the axial of the motor shaft is 5mm and the gear portion take up 2.5mm of the overall length. The motor shaft measures 1.48mm (probably should be 1.5mm).
Re: PC Engine cd-rom gear
It's very close, but the diameter is larger than necessary.BuffaloWing wrote: ↑Wed Feb 14, 2024 3:41 amYou might want to use Dreamcast's gear. I have a broken laser on top of my desk and took some measurements. It has 14 teeth like your picture, so it seems like that maybe a standard... Anyway, the diameter is 4.76mm (probably 4.75m theoretically), overall length along the axial of the motor shaft is 5mm and the gear portion take up 2.5mm of the overall length. The motor shaft measures 1.48mm (probably should be 1.5mm).
However, now I have a reference, I will model several options and try to print it tomorrow.
Spoiler
Re: PC Engine cd-rom gear
So I printed out the gears in several sizes. In my opinion, the best fit was 4.35mm in diameter. The CD-Rom works, but the sound is interrupted.
Could this be a mispositioning of the laser head due to an incorrect gear? Or can this be fixed by adjusting the potentiometers?
Demonstration of the problem here.
Could this be a mispositioning of the laser head due to an incorrect gear? Or can this be fixed by adjusting the potentiometers?
Demonstration of the problem here.
Re: PC Engine cd-rom gear
I would strongly advise caution if planning to play with pots. Unless you know what you are doing, laser pots, especially when plural, are a nightmare to adjust right. Chances are good the problem is the gear. Also the old CD-ROM2 drives were notoriously finicky, audio drop outs are to be expected unless you have a mint unit, even then they prolly worked best when actually fresh out of the factory and even, even then they weren't all that great.
If you do try to adjust the pots make sure to mark exactly where they were from the factory so you can at least go back to that.
If you do try to adjust the pots make sure to mark exactly where they were from the factory so you can at least go back to that.