Yet another Neo Geo MVS console Kit (CMVS)
-
Chipnetics
- Posts: 86
- Joined: Wed Jul 11, 2018 4:08 pm
- Location: Alberta
- Contact:
Yet another Neo Geo MVS console Kit (CMVS)
Hi All,
Thought I'd share one of my latest designs. Actually I've sat on this one for some time but finally have a little more bandwidth to pump out units for sale....
As the title implies, it's a kit to make your own Neo Geo console from original MVS boards (often referred to as 'CMVS'). This kit will work with Neo Geo MVS boards with model number MV1C.
The differentiator on this one being that it supports Super Nintendo controllers in place of Neo Geo controllers, making it much more affordable to get into Neo Geo. The board has two ATTINY-2313 ICs that turn the serial data from a SNES controller into parallel data, without any lag! I wrote the code in a combination of BASIC and Assembly and have open sourced it on GitHub.
This board outputs a 15Khz RGB signal, exactly as produced by the Jamma edge connector, with Csync acting as Hsync; thus you will have to utilize a proper monitor, or video upscaler, that can support this signal as it is a low horizontal refresh frequency not commonly supported by modern equipment.
There is a jumper to route Csync through a 470 ohm resistor if required (in cases of non TTL equipment). Also on the latest design I've added circuitry on the RGB lines if you'd like to install any resistors on the RGB lines to limit current, or even form a voltage divider to knock down voltage; for exotic/specific cases. (I really wanted to make sure all display/monitor scenarios were covered!).
Units come with a 3amp Triad Magnetics power supply, and have been tested working with 161-in-1 game carts!
You can purchase from my Tindie Store at the link below:
https://www.tindie.com/products/chipnet ... herboards/
Obligatory photos:
Thanks y'all!
Thought I'd share one of my latest designs. Actually I've sat on this one for some time but finally have a little more bandwidth to pump out units for sale....
As the title implies, it's a kit to make your own Neo Geo console from original MVS boards (often referred to as 'CMVS'). This kit will work with Neo Geo MVS boards with model number MV1C.
The differentiator on this one being that it supports Super Nintendo controllers in place of Neo Geo controllers, making it much more affordable to get into Neo Geo. The board has two ATTINY-2313 ICs that turn the serial data from a SNES controller into parallel data, without any lag! I wrote the code in a combination of BASIC and Assembly and have open sourced it on GitHub.
This board outputs a 15Khz RGB signal, exactly as produced by the Jamma edge connector, with Csync acting as Hsync; thus you will have to utilize a proper monitor, or video upscaler, that can support this signal as it is a low horizontal refresh frequency not commonly supported by modern equipment.
There is a jumper to route Csync through a 470 ohm resistor if required (in cases of non TTL equipment). Also on the latest design I've added circuitry on the RGB lines if you'd like to install any resistors on the RGB lines to limit current, or even form a voltage divider to knock down voltage; for exotic/specific cases. (I really wanted to make sure all display/monitor scenarios were covered!).
Units come with a 3amp Triad Magnetics power supply, and have been tested working with 161-in-1 game carts!
You can purchase from my Tindie Store at the link below:
https://www.tindie.com/products/chipnet ... herboards/
Obligatory photos:
Thanks y'all!
Re: Yet another Neo Geo MVS console Kit (CMVS)
Hey! This looks great and landed at just the right time for me. Just ordered the assembled kit
-
Chipnetics
- Posts: 86
- Joined: Wed Jul 11, 2018 4:08 pm
- Location: Alberta
- Contact:
Re: Yet another Neo Geo MVS console Kit (CMVS)
Awesome thanks so much for the support!
Sent from my CLT-L04 using Tapatalk
Sent from my CLT-L04 using Tapatalk
Re: Yet another Neo Geo MVS console Kit (CMVS)
Nice design. I think this will be a popular item.
-
- Posts: 315
- Joined: Sat Mar 17, 2018 2:49 pm
- Location: Germany
Re: Yet another Neo Geo MVS console Kit (CMVS)
This looks really cool!
About the VGA output: does Pin 9 of the VGA port provide 5V DC? That way it would be possible to build a SCART cable with attenuating resistors in the RGB lines.
About the VGA output: does Pin 9 of the VGA port provide 5V DC? That way it would be possible to build a SCART cable with attenuating resistors in the RGB lines.
-
Chipnetics
- Posts: 86
- Joined: Wed Jul 11, 2018 4:08 pm
- Location: Alberta
- Contact:
Re: Yet another Neo Geo MVS console Kit (CMVS)
I'll admit, I didn't pump 5V on Pin 9; I even grounded it instead of leaving it floating. Really if the demand was there, it's pretty easy to add the extra trace in the next PCB run come a month or so.SuperSpongo wrote:This looks really cool!
About the VGA output: does Pin 9 of the VGA port provide 5V DC? That way it would be possible to build a SCART cable with attenuating resistors in the RGB lines.
Thanks for the kind comments all!
-
- Posts: 315
- Joined: Sat Mar 17, 2018 2:49 pm
- Location: Germany
Re: Yet another Neo Geo MVS console Kit (CMVS)
Yeah, I was afraid of that This being a kit would have made it easy to add one wire to the pin. If you ever end up doing a redesign, maybe you could indeed leave the pin floating
-
maxtherabbit
- Posts: 1763
- Joined: Mon Mar 05, 2018 4:03 pm
Re: Yet another Neo Geo MVS console Kit (CMVS)
Yes - please float pin 9 on any source device anyone builds vs grounding it. Early VGA cards as a general rule floated it, before DDC support came around.SuperSpongo wrote:Yeah, I was afraid of that This being a kit would have made it easy to add one wire to the pin. If you ever end up doing a redesign, maybe you could indeed leave the pin floating
Re: Yet another Neo Geo MVS console Kit (CMVS)
Hey, can you educate me as to why that would be needed? Is that to enable RGB on a Consumer TV without needing to go through something like a Syncblaster?SuperSpongo wrote:This looks really cool!
About the VGA output: does Pin 9 of the VGA port provide 5V DC? That way it would be possible to build a SCART cable with attenuating resistors in the RGB lines.
-
Chipnetics
- Posts: 86
- Joined: Wed Jul 11, 2018 4:08 pm
- Location: Alberta
- Contact:
Re: Yet another Neo Geo MVS console Kit (CMVS)
Really to power additional video devices without having to use extra power adapters. (For example a syncstrike can be powered over scart or via external psu.) It's just an extra way to pass on power to other devices, that's of course if the device on the receiving end is wired to accept power on pin 9 as well. It never really hurts to pass on power; I had just left it absent mostly due to space constraints on the bezel of this pcb design; also the neo geo with a 161 cart already draws quite a few amps and didn't want the bit of headroom left to be eaten up from other devices through vga power - albeit someone could just use a bigger psu.
Sent from my CLT-L04 using Tapatalk
Sent from my CLT-L04 using Tapatalk
-
- Posts: 315
- Joined: Sat Mar 17, 2018 2:49 pm
- Location: Germany
Re: Yet another Neo Geo MVS console Kit (CMVS)
Yes, most TVs in Europe need a blanking signal on Pin 16 to switch to RGB.JigsawMan wrote:Is that to enable RGB on a Consumer TV
RGB cables usually come with a 180 Ohm resistor to create a voltage divider with the TV's internal 75 Ohm resistor.Wikipedia wrote: 0..0,4 V– (low = FBAS), 1..3 V– (high = RGB) @ Z = 75 Ohm