shmups.system11.org

Shmups Forum
 
* FAQ    * Search
 * Register  * Login 
It is currently Sun Dec 15, 2019 5:31 am View unanswered posts
View active topics



Post new topic Reply to topic  [ 3 posts ] 
Author Message
 Post subject: Setting up BVM-D24E1WU
PostPosted: Thu Nov 21, 2019 8:22 pm 



Joined: 21 Nov 2019
Posts: 1
I managed to get one of these things, but I'm still new to learning about everything you need set up for retro gaming, and I was wondering if I could find some assistance here. I have the monitor and the control unit under-mounted, and I only have the default analog board, which is all I think I need for most systems anyways? I have 4 separate 75 ohm terminators, but that's it.

I know I have to buy a couple of RCA to BNC adapters, but there's a 4th spot on the board for SYNC In and Out, do I need to connect anything to that? I'm primarily going to be using my Wii over component cables, and playing some games through the VC on that in 240p. If I don't need to connect anything to the sync in and out ports, then do I need anything other than 3 rca to bnc adapters and just plug the 3 component cables right in?

I didn't get a power cord with this, I'm assuming any power cord that I use to plug into any other monitors I have would be fine right? And for storage, is it a bad idea to have it on a carpet floor?

Sorry for asking some really silly questions, but I've tried researching with the little free time I have on my own and I haven't been able to figure it all out since everyone's setups seem to depend on which type of monitor they have.


Top
 Offline Profile  
 
 Post subject: Re: Setting up BVM-D24E1WU
PostPosted: Fri Nov 29, 2019 11:58 am 



Joined: 22 Nov 2019
Posts: 2
The Wii component cables carry the picture's sync data over the green cable (Y). You will not be using external sync, don't worry about leaving that plug empty. You may need to select YPrPr in the D24's input settings, because the Wii is not putting out RGB.

Any power cord is probably fine, but I would choose your thickest one. The manual says 16-18 AWG is ideal, and if you're uncertain about the ones you have laying around, these are not expensive: https://www.monoprice.com/product?p_id=27285

I don't see an issue with storing it on a carpet floor. The manual suggests you should not use it on a carpeted surface, however. Here is what the manual says about storing the unit:

Storage and transport conditions
Temperature
–10°C to 40°C (14°F to 104°F)
Humidity
0% to 90%
Pressure
700 hPa to 1060 hPa


Top
 Offline Profile  
 
 Post subject: Re: Setting up BVM-D24E1WU
PostPosted: Sat Nov 30, 2019 3:51 am 



Joined: 14 Aug 2017
Posts: 708
You should be all good with that. Just remember you need the terminators on the out connectors whenever you have something coming in through the in connectors. You can leave the fourth one attached to the external sync out connector in case you ever need to plug something in there.

BTW, it'd be a real shame to not take advantage of a monitor like this for other uses, beyond just retro gaming or gaming in general. It's after all a broadcast monitor, and interlaced content therefore shines on it. You can get an amazing full HD/1080i picture on it. You can use HDMI sources via either an HDMI to component cable or, better but more complicated, an HDMI to VGA (RGBHV) adapter + sync combiner to get RGB for the monitor. Your movies, TV shows, anime, etc., both old and new will look great on it.


Top
 Offline Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 3 posts ] 

All times are UTC


Who is online

Users browsing this forum: FinalBaton, strayan and 17 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
Space Pilot 3K template by Jakob Persson
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group